They gave you the equipment. Nobody gave you the method.

You run the rover, the total station or the company drone, and you learned it on the job, one problem at a time. The Survey School fills in what the job never explained: why it works, how to check it, and what to do when the numbers do not agree.

Join The Survey School

Member results in the video are their own and are not typical.

If you learned it on the job, you know these.

“I only ever get float. I cannot tell if it is the receiver, the corrections or me.”
“We were out by a couple of tenths and nobody could say why.”
“I was shown which buttons to press. Nobody explained the reasons.”
“I have the field side down. The data side is a harsh learning curve.”
“My boss does not trust the GPS elevations, and I cannot prove him wrong.”
“I want to be useful in the field, not just carry the rod.”

Most companies are too busy to train. That is not a knock on anyone. It just means the reasons behind the work have to come from somewhere else.

Diagnose. Adjust. Deliver.

You already do the work. This gives you the reasons behind it: how to know a result is right, how to fix it at the cause, and how to hand over something the office can rely on.

Diagnose

Know whether your data is right before it leaves your hands.

Check it against control and independent checkpoints, and learn to read what the numbers are telling you. Good and bad stop looking the same.

Control points

Tolerance σ 0.015 m

PointσX (m)σY (m)
CP-010.0060.008
CP-020.0110.009
CP-030.0240.019
CP-040.0070.031
CP-050.0090.012
CP-060.0280.026

3 of 6 points over tolerance

One variable at a time

CoordinatesNot checked
NAD83(HARN)
Antenna heightNot checked
1.800 m measured to the ARP
GeoidNot checked
GEOID12B
A finished boundary and topographic survey drawing: parcels, buildings, parking, contours, spot elevations, a legend and survey notes
Boundary and topographic surveyChecked
Checking control pointsDiagnose

01

Diagnose

Know whether your data is right before it leaves your hands.

Check it against control and independent checkpoints, and learn to read what the numbers are telling you. Good and bad stop looking the same.

Control points

Tolerance σ 0.015 m

PointσX (m)σY (m)
CP-010.0060.008
CP-020.0110.009
CP-030.0240.019
CP-040.0070.031
CP-050.0090.012
CP-060.0280.026

3 of 6 points over tolerance

02

Adjust

Fix it at the cause, not at the desk.

Datums, antenna heights, geoid models, base setup, ground control. One variable at a time, with a reason for each, so the error stops showing up.

One variable at a time

CoordinatesFixed
NAD83(HARN)→ Transformed to NAD83(2011)
Antenna heightFixed
1.800 m measured to the ARP→ +0.044 m = 1.844 m to the antenna phase center
GeoidFixed
GEOID12B→ GEOID18

03

Deliver

Hand over a deliverable a client will pay for.

A finished topo built on checked control, with the accuracy written down, ready for the surveyor or engineer who relies on it. That is the work clients pay for.

A finished boundary and topographic survey drawing: parcels, buildings, parking, contours, spot elevations, a legend and survey notes
Boundary and topographic surveyChecked

If the whole crew needs this, there is a team plan.

Seats for each person, and a manager view that shows who has finished what and how they scored. Rami sets every team up himself, on a call.

Wins from the community.

Posted by members in the community, in their own words.

Mark NielsenApril 2025

Summer student on a 1.2 km bridge

“The project is a 1.2 km-long elevated bridge for a transit project. I was asked to give the surveyor a hand. He didn't expect much... He didn't know I'm also a survey school student here, and the information I've gained here is paying off well.”
A total station on a tripod set up on a sidewalk next to a construction site
Michael LilleyDecember 2025

Work through 2028

“After we got done he asked if I had my drone, of course I did... I said okay, he said good, because you're flying for us. Job doesn't start until April of 27, it's a design/build and the architect want a rough idea of where everything is and a close topo.”
Brook StocktonOctober 2026

My first resection

“I've never used a total station until today. Did my first resection with the A100. I used two RTK control points for the resection and held a third RTK point out as an independent check.”
A total station on a tripod in a grassy field with a GNSS pole behind it
James SnelsonMay 2026

New job

“I was recently hired and started with a local water/waste water/civil engineering firm. It is quite the stretch for me being a mechanical engineer but I'm really enjoying it so far.”
Andrew WalkerJuly 2025

My first plat

“I just finished my first PLAT from start to finish!! It had to be signed by my boss of course, but it was a very enlightening experience to see just how much work it takes to make one property into two.”
Thomas EschJune 2026

Pix4Dmatic Trainer Certification

“Completed the coursework and training and passed the Pix4Dmatic Trainer Certification exam... My son, James, also passed the Trainer Certification exam yesterday.”
A Pix4D certificate recognising Thomas Esch for completing the PIX4Dmatic trainer certification exam
J BaeJuly 2025

From carpenter to BIM field specialist

“I've created an incredible opportunity with a general contractor to handle layout using a total station and collaborate with their BIM team.”
Todd K CollinsMay 2026

Speaking to Florida's property appraisers

“I had the opportunity to attend the Florida State Property Appraisers Annual Conference and... was able to speak to... Property Appraisers from Florida about the benefit of using drones to conduct flight missions and collect current data on properties.”
A conference room with a speaker at a table before the session
Joseph EdwardsMarch 2025

Back to surveying

“Good news! I just got hired by a surveying firm and start on Monday.”
Alan SwensonMarch 2025

Earned an Emlid Reach RS2+

“Thanks Rami Tamimi and everyone at The Survey School who helped me get to level 7 to be lucky enough to earn this RS2+. I can't wait to put it to use.”
An Emlid Reach RS2+ receiver in its case on a desk
Hugh TullApril 2025

Accepted into Advanced Geomatics

“I just got accepted into BCIT's Advanced Geomatics program! Here's the cool part: instead of the full 2-year program, I'll be jumping straight into 2nd year... Feels like a natural progression after all we've been learning here in the Survey School community.”
Peter MorssinkJune 2026

A full set

“I received my RS3 and now I have a full set simplifying my workflow.”
Two Emlid GNSS receivers side by side in their cases
Al SpinaMarch 2025

Growing in a new field

“Thank you all for helping me grow in this new field and being a part of a great community! I received this wonderful tool today that will certainly help me grow and become more marketable.”
A boxed Emlid receiver on a counter

Each result is the member's own and is not typical.

What members say

Meet your instructors.

Two are licensed surveyors, and all four have done this work for a living. They show you what they look for in work like yours and how to get it right the first time.

  • Rami Tamimi, P.S.

    Rami Tamimi, P.S.

    Professional Surveyor · PhD Candidate, Geodetic Engineering, OSU · Founder

    Over a decade of land development experience, plus three years tuning sensor alignment for self-driving systems. Teaches drones, LiDAR and photogrammetry, and the survey fundamentals that make them accurate.

  • Joe Nelson, PLS

    Joe Nelson, PLS

    Licensed Professional Land Surveyor

    Project Manager at BKF Engineers with 14 years of professional surveying. Teaches how survey work gets done on real projects: boundary, topo, ALTA, control networks, and final maps ready for stamp.

  • Dr. Joseph Kerski, PhD GISP

    Dr. Joseph Kerski, PhD GISP

    PhD Geography · GISP · Author of 12 books · Former Esri Education Manager

    Geographer and GIS educator with three degrees in geography and 22 years across NOAA, Census, and USGS. Teaches GIS and spatial analysis.

  • Barry Bassnett

    Barry Bassnett

    Cartography and photogrammetry · 45 years

    Forty-five years in cartography and photogrammetry: aerial, close range and underwater.

Also on the team: Dr. Ryan Hughes (Pix4D, head of training) and Mariana (Emlid, technical support).

Who this is for.

It fits if

  • You do layout, stakeout, topo or as-builts for a contractor, an engineering firm or a survey crew.
  • You are the one your company gave the drone, the scanner or the new receiver to.
  • You want to understand the work well enough to be trusted with more of it.

It is not for you if

  • You only want to know which buttons to press. We teach why, and that takes some effort.
  • You are looking for a shortcut to a license. This is training, not a credential.

One membership. Pay monthly or yearly.

Monthly

$249a month

  • Every course, one opening every 30 days
  • The weekly live lecture and Q&A
  • The community, with licensed surveyors answering

Yearly

$1,988a year

  • Everything in monthly
  • Pix4Dmatic Pro, an Emlid Reach GNSS receiver, Emlid Flow Pro and GEODNET corrections, unlocked as you reach higher levels in the community

You join on Skool, where the plan details and the levels are shown before you pay.

Questions people ask before joining.

Be the one on the crew who knows why.

Join on Skool, monthly or yearly. The first course opens the day you join, and the weekly live session is where you bring the problem from this week.